GC3277XUAM Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tara from ALBANY, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SAN DIEGO, CA
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replaced upper over light and assembly
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra M from DISTRICT HTS, MD
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks were old
Replace the racks. No special instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from WINCHESTER, MA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mz from COLUMBIA, ME
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURBANK, CA
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from San Juan Capistrano, CA
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The floor panel of the oven was pocked and in bad shape
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Lynn, MA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Rubber seal was broken
Broke the same day I installed it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from APACHE JUNCTION, AZ
- Parts Used:
- 7403P067-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven light Switch
Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lancaster, NY
- Parts Used:
- 12400043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken oven door hinge
Oven is built in. The only way to access the hinges is to pull the oven out and remove the sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael P from Hickory Hills, IL
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door seal was pulled out by grandson.
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Dover, DE
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged the oven lamp socket while removing a broken bulb.
Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.
Was this instruction helpful to you?
Thank you for voting!