ESD394 Maytag Range - Instructions

Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)

I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part!

Went together real easy , but I poped a fuse/circuit braker.
The braker would not reset at first, but we got it all working fine.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.

Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hooks towards the front of the oven near the door and removed.

The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.

After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.

Good to go now!

just plugged it in!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The repair went real easy. Turned off power, unscrewed two screws at back of oven and disconnected the two wires. Reconnected two wires to new broiler element and remounted the new one with the two screws. Turned the breaker back on and had a steak cooking in no time.

Shut off power to the oven.
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Replaced with the new burner works like new. Thanks a bunch!

I had My friend from church come over and look at the problem. He said that it could be fixed, so he looked up the part and ordered the part. It came in two days, it took about 15 minutes to install the part and put the back back on. It was that easy! Thank you! Now i don't have to buy a new stove!!