CBR1430BGH Maytag Range - Instructions

i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

My top burners and broiler were working fine so I knew it was not a gas pressure issue,after reading other peoples oven issues I felt comfortable that my problem was the oven igniter, the igniter was only building about 50 to 75 percent of the normal glow/heat needed, thereby not creating enough heat to trip the sensor that opens the oven burner gas valve. 2 Screws hold a drip pan which after removed allow access to the igniter. 2 Screws hold the igniter in. You need to access the rear of the stove to plug in the new igniter connector at a 1 screw access panel in the center of the back of stove. My oven has been working great since the repair. I would recomend partselect anytime, I ordered the wrong igniter, the diagram is confusing so be carefull , and had to send it back , I got my refund in less than a week. Good luck from beautiful western new york state.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

I replaced the igniter.

Followed the instructions that were provided me when I ordered the Gas Oven Igniter

I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!

Got the part, changed it, works great. That's all

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.

used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

easy

unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.