Models > BCRE905 > Instructions

BCRE905 Maytag Range - Instructions

Jump to:

All Instructions for the BCRE905

Customer:: Max from Bothell, WA
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would not heat up properly to set temperature

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Was this instruction helpful to you?

Customer:: Lloyd from Eau Claire, WI
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

change oven sensor

Followed provided video

Was this instruction helpful to you?

Customer:: Jeremie from Freeland, WA
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Easy installation

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Was this instruction helpful to you?

Customer:: Judy from McKinney, TX
Parts Used:: WP7711P492-60
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken plastic knob

Placed new knob directly on post. No problem

Was this instruction helpful to you?

Customer:: John from Dacula, GA
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Fan runs continually ,door locked,error code f2,f3,f7

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

Was this instruction helpful to you?

Customer:: MARK from roseville, MN
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would overheat

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Was this instruction helpful to you?

Customer:: Grant from Alexandria, VA
Parts Used:: 8009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Was this instruction helpful to you?

Customer:: Timothy from Longmeadow, MA
Parts Used:: 12001656, 8009
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Oven have F2 and F3 codes following cleaning cycle making oven inoperable

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

Was this instruction helpful to you?

Customer:: Stacey from Tampa, FL
Parts Used:: 12001656
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would not turn on

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

Was this instruction helpful to you?

All Instructions for the BCRE905