CRE500 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Phillipsburg, NJ
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wire broken off plug in block
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from reading, MA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
contacts had gotten burnt out/blackened with age so burner was intermittent.
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Grand Marais, MN
- Parts Used:
- WP7406P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bake element was broken,
PartSelect web site correctly identified the replacement part, told me it was in stock and provide complete written directions on how to replace the part. Not being mechanically inclined I was skeptical, however disconnecting the power, removing the back shield and unclipping the element, removing the two screws inside the oven connecting the element to the back of the oven and carefully sliding out the old element, then reversing the procedure was simple, easy, quick, AND IT WORKED. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Price, UT
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stove burner no longer would heat up burner element
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Edmonds, WA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned out surface element
I pulled the old one out and installed the new one. Never broke a sweat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Tigard, OR
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
failed heating element
Took out of package and plugged in. turned on. It took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Goodlettsville, TN
- Parts Used:
- WPY04100166, WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My burners were replacements that rocked and were uneven.
I unplugged the old ones and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Desoto, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!