CDE8300ADB Maytag Range - Instructions

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

First Inserted 2x4x 36" length of wood behind the spring loaded door hinges to ease removing the oven door as I worked alone (this was recommended in a previous post and was essential when working alone, TY). Removed 2 retaining screws on the interior side of the door at the hinge locations. Slid the door up an off the hinges, moved door to a cloth pad protected work bench. Took the door and glass panels apart removing all the related screws, retaining clips; taking note of screws, retaining clip and panel locations for reassembly. Removed the insulation, removed the glass window pack, and removed of all rust fragments (dust) between the 2 glass window panels. The glass window pack metal molding retainer, on the oven interior side of the glass window had completely rusted away. Removed the existing oven door gasket. Cleaned the glass door window pack, and interior side of the oven door surface. Installed the new gasket, which fit very well. Tightened the loose door handle screws. Reassembled in reverse order all door components noted above, and replaced the door onto the hinges, fastened the 2 door hinge screws, removed the 2x4x36" wedge holding the hinges in the open position, and closed the door. Job complete. Thanks to previously posted directions as a good guide. Hope this helps as well.

Fortunate to have the replacement parts available.
Wish a replacement door window pack was available, as the double glass, metal edge seal is deteriorating, and the metal molding retainer that held the glass in place is completely rusted away on the oven side of the existing window pack. Plan to find heat resistant caulk to seal the glass in the door, in lieu of the metal molding glass retainer.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

Removed the 4 screws on the bottom of the panel, lifted the panel out and up to clear the uper part of the panel. Removed the screws from the left and right switches, which hold the bracket of the clock, marked the wires of the clock and removed the wires. Installed the new clock in reverse. The power to the range was off.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Much to my horror, what was described as a simple, 15-minute replacement, took 3 days! In order to replace the oven door gasket, I had to disassemble the entire door. Every photo I saw of the gasket showed it as a flexible part: gently pull out the old one and push in the new. What I received in my order had a frame. In order to replace it, I needed to unscrew the door parts. Unfortunately, I made a few rookie errors, primarily because I kept thinking the next screw would release the gasket frame. So I neglected to keep track of the screws I removed, and I didn’t take any photos!
I must have used half a roll of masking tape to keep parts together; I did not have 5 hands! When I released everything and nestled in the frame, I had even more trouble replacing all the screws I took out. The majority of holes did not line up. So I just did the best I could, put in as many screws as I could. But after three days of working, I finally finished. It all held together, and the door did what it was designed to do. Really a repair horror. And I am not an incompetent novice!

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

Replace filter

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve