MER6555ACW Maytag Range - Instructions

Shipped on timely manner,I will order again from Part Select, installing was a 15 minute job, that what I did, 1 unplugged stove, 2) removed 4 screws, (2 on top bracket and 2 on back) , 3) slide unit out couple inches enough to disconnected the wires from each end of unit and removed old part, installed new unit by reconnecting end wires, pushing unit slowly toward back of oven until wires find it's right position, set it back in place with the 2 screws on top bracket and 2 screws on back, done!!

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

PULLED THE POWER CORD!! Loosened a couple of screws holding the element to the rear oven wall, removed the electrical wires (red on left, yellow on right) attached to the baking element, removed old element, inserted new element and reattached the wires respectively thereto. One minor glitch did occur. The RED wire inadvertently slipped back through the hole into the insulation and was not retrievable. I removed the small metal plate housing the wires on the back bottom of the stove, pushed the red wire (plentiful length) back into the oven, reinstalled the plate, connected the red wire to the bake element, reconnected the power, element began to heat. Mission accomplished. One caution: Pay attention to the SHAPE of the failed element before ordering online or buying in person.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

We removed the rear panel, then removed the stove top, then removed the sides. We undid the straps that hold the insulation in place. Pulled out the old insulation and put in the new. Replaced every thing we took off. The nastiest thing was the old insulation full of mouse droppings and even a few dead mice.

I pulled the range out, unplugged it and removed the back panel with a Phillips-head screwdriver. I then removed the two screws inside the oven that holds the element in place. I located the two wires on the back of the range attached to the element. I gently pulled off the wires using a pliers and then easily removed the burned out element. I put the ends of the replacement element into the respective holes, screwed them in and then plugged the wires back on at the back of the range. After replacing the back panel, I plugged the range back in. I turned the oven on with an oven thermometer inside, to test it out. I imagine I saved at least a couple of hundred dollars for the repair with this simple DIY, if not, the cost of a new double oven range!

not to offend anybody but what i learned on prior posts helped alot..
1. remove unit and unplug.
2. remove door by opening to 45 degree angle and lifting door face towards you.
3. remove back panel to unit.e.
4.unscrew burner element from back inside of oven.
5.gently pry clip off each off burner element from rear of unit. Pull gently towards you.
6.unscrew support from inside oven.
7. remove old element and just reverse directions to reinstall.

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !