MGR4452BDB Maytag Range - Instructions

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.

Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.

The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.

Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.

Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.

Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.

Piece of cake, really.

Total repair time: about 30 minutes, including the mandatory halfway beer break.

Removed the oven door an removed some screws. After that it was pretty much self explanatory from there. Real simple project !

Firmly grasp burner turn counter clockwise while lifting. Photograph the location of the wires. Remove with a Phillips head screwdriver. The igniter will lift and turn one quarter turn then pull through bottom. Reverse the steps to install the new igniter. Test knew igniter. Put tools away

Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

It was a very easy repair. I just connected the two wires to the bottom of the electrode and set the burner on stove top and turned it to the right to lock in place. Turned burner knob on and burner worked great.