MGR5750ADQ Maytag Range - Instructions

turned burner counterclockwise and removed it reversed procedure and installed new one..

Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!

Put a new one in.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.

replaced heat sensor

Very simple! Unscrewed the burner heads with a simple twist, unplugged the two wires from the old head, plugged them into the new one, then screwed that back in. The flames are MUCH better - more efficient and safe. thank you! ( Only issue was when we ordered we didn't see a choice of color and the new ones are different, but it really doesn't matter on an older stove anyway.)

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

First I removed the old burner head by twisting it counter clockwise by using wide channel lock pliers. When It completely came off, the burner head had deteriorated so much that it almost came apart. When I took off the 2 wires from the burner head it also easily came apart. The burner-head was in really bad condition. I cleaned the whole area and connected the 2 wires to the new burner head and hand tightened in a clokwise direcrtion. It took 20 minutes to install.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.