MER6741BAS Maytag Range - Instructions

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

remove two screws, remove two slide on wire connections and remove element. reverse to install.

First I unpluged the range from the power source. Then I removed the back cover, disconnected the two wires to the element, remover two screws on the inside of the oven the held the element in place and removed it. I then installed the new element in the reverse order. This took about one day to get the new part and 15 to 20 mins to do the repairs. I figured that I saved at least $55 on a repairman service call.

I removed the two screws, puled out the element and took the pliers to unhook the two wires.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

First I unplugged the range from the wall outlet power source...VERY IMPORTANT!!! Then I unscrewed the 2 mounts in the back of the range that hold the heating element in place. I removed the old and installed the new one and reattached the 2 new mounts with the original screws and plugged the range back into the wall outlet. Other than the small and dark work space inside the small oven, it was super easy to do and probably saved us $175!

Hiring a repair man was going to be expensive, and I saw the part was cheap and others had said this was an easy job to do. I figured I'd give it a shot even though I have very little experience repairing things and there was no help coming from my husband. I followed the instruction of others, unscrewing two screws and pulling the broken element out. The metal that capped the ends of the broken piece needed to be removed. One came off easily. The other took a bit of wiggling to get off. A mistake I made was, by accident, one of the wires coming from behind the stove got pushed back through the hole in the oven wall.. I needed to fish it out with tweezers, but thankfully, that was easily retrieved. Once I put the caps on the new piece, I had some trouble reaching the plate to screw it back into place. I removed the oven door, which helped a lot, but then found it a little tricky to get the oven door back on. Despite the little set backs, I still did it myself in around 15 minutes. I'm delighted to have my oven back without paying a fortune!

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

watched how to video so was prepared for a standard install. removed screws and coverplate...disconnected wires...threaded new element thru coverplate...reconnected wires...reinstalled coverplate with screws. disconnecting and reconnecting wires took some thought and patience, but wasn't rocket science.

First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out