Models > MBR1415AGS > Instructions

MBR1415AGS Maytag Range - Instructions

Jump to:

All Instructions for the MBR1415AGS

Customer:: Mary from WINCHESTER, MA
Parts Used:: WP7212P043-60
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

1960's oven door gasket fell apart, actual gasket not available any more

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Phyllis from BROWNVILLE, NY
Parts Used:: W11665456
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Wrench (Adjustable)

My original back leg broke because the floor is uneven. Had to pull it out several times.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Anita from ELKTON, VA
Parts Used:: WP7212P043-60
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers

My oven door seal had dried rotted

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Mz from COLUMBIA, ME
Parts Used:: WP7212P043-60
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Linda from BURBANK, CA
Parts Used:: WP7801P173-60
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Original rack had melted plastic on it.

Removed the original rack. Checked dimensions, installed the new rack.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Donald from Mokena, IL
Parts Used:: 74007498
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

old igniter wouldn't get hot enough to allow gas flow

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: William from Rockford, MI
Parts Used:: 74007498
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Oven burner will not light consistantly

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Godfrey from new york, NY
Parts Used:: 74007498
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Wrench set

The igniter was just glowing and it didn't open the gas valve

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Stacey from Woverine Lake, MI
Parts Used:: 74007498
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

Oven wouldn't heat

I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Richard from Gloucester, MA
Parts Used:: 74007498
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers, Wrench (Adjustable)

Broiler would not ignite

I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Fred from Suwannee, FL
Parts Used:: 74007498
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Oven very slow to light on bake mode. Gas smell.

First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Steven from Goshen, IN
Parts Used:: 74007498
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

The main gas valve to the oven would not stay on.

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Roger from San Juan Capistrano, CA
Parts Used:: WP5504M003-19
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The floor panel of the oven was pocked and in bad shape

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: W from Jonesboro, GA
Parts Used:: 74007498
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

oven pilot glow only

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Kathryn from Carol Stream, IL
Parts Used:: WPW10348409
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Screws on the door of the dishwasher were very loose.

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the MBR1415AGS