MEP5775BAB Maytag Range - Instructions

Remove 6 screws fastening element to top of oven. Remove most of the screws from the back and pull away from oven. Use pliers and pull wires off of element connectors.Remove 2 screws fastening element to rear of oven. Install new element with fastening screws. Re-Install wires and fasten back of oven. Re-install the six screws to fasten element to top of oven.

Pulled oven out unplugged the unit unplugged broiler unscrewed broiler from inside repeated the process backwards turned oven back on

Bottom door/ simply removed the screws where neccessary and slipped the glass off with trim attached , then carefully seperated the trim and window , cleaned glass and put new trim on with the tape shims in place. reinstalled screws. Top Door/ using trim made for the bottom door , I seperated the bottom from the sides bydrilling the welds then used the existing sides with the bottom section of the new piece which I had seperated . It worked very well and there was no way to simply buy trim for the top door. It is Paul

looked on internet on how to remove top. an easy fix after watching video

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

SHUT OFF POWER AT BREAKER BOX! Remove oven door, use nut driver to remove two screws holding old element to back of oven. Pull forward to get wires into oven, remove wire clips from old part and re-attach to new element using pliers. Re-attach to back of oven, replace door. Turn on power and heat oven to burn off coating on new element. Not at all difficult, except for wire clips are at angle to wire, making re-attachment a bit difficult to do. DO NOT LOSE WIRES INTO BACK AS THEY WOULD BE VERY DIFFICULT TO RESCUE IN A JENN-AIR SLIDE IN UNIT LIKE OURS.

Removed the top after some trouble(must pull stove out all the way)rplaced parts

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Took two hex head screws out. Pulled element out slow. Got slack pulled off connections. Reverse order for install

The new element wiring placements were totally different from the old element. Lucky for me the lettering printed on the terminals for each pole was the same as on the old one. It was just a matter of matching up each terminal pole lettering. The instructions that came with the new element were of no help at all. Youtube was my best helper.

un-plug device from outlet for safety first and then remover all top panel after screws lower two side small screws. actually is not selector problem. It was burner switch problem for 6 inches element.