CRE9530CDE Maytag Range - Instructions

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was fixing the oven element my wife replaced the oven light.

came only I had to order the set again

Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Removed old hinges, fabricated new mounting plates from 16ga steel plate. . . Cut new hinges to fit in available space. . . Drilled and tapped new mounting holes and adjustment tracks. . . Shortened existing springs to fit new configuration. Installed new hinges.

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.

Don Samuelson