AER1360AGW Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ANNIE from LINDEN, NJ
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Baking Element In The Oven Had Broken
My husband did it was really easy ,he turned the power off to the stove,took the back cover off the stove with a screwdriver and pulled the old one out,then he slipped the new one in connected the wires ,it took less than 15 minutes that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stanley from south lake tahoe, CA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken bake element
Took out two screws in the back of the oven that held in the bake element. Pulled the element out of the back of the oven to expose the wires. Pulled the wires off the broken element and then reattached the wires to the new element, put it back into place. Reattached the screws. Done in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Davenport, FL
- Parts Used:
- 74003370, WP74003369
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken control panel ends
slid out the range removed the old replaced it with the new. very easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shawn from Vancouver, WA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Sturgeon Bay, WI
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat in oven
Your site really helped out alot. Job was farily easy and now we have heat. Difficult part was reaching the wires in the back. Thanks again! TZak
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Jesup, GA
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace oven heating element
The process would have been easy except the wiring to the element had a problem. One wire was too short which meant pulling the entire stove assembly out to reroute the wire.The part worked fine; the problem was with initial wiring of stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Young from Cordova, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
one of wire melted and broken off from receptacle
Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.
It's easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from Hillsboro, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Electrical receptacle for burner was defective.
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIMBERLY from INDIANAPOLIS, IN
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element went out
Just followed the installation instructions offered on this website. WAS REALLY EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from greendale, WI
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a new electric coil for my electric stove.
I looked up the part from the parts diagram list and was easily able to order it. The part arrived quickly and I installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Manchester, MD
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Sockets for the burner elementss were burned out
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice M from Ocala, FL
- Parts Used:
- WPW10259868
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 of the small burners just fell apart
I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Crestwood, MO
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken leveling leg.
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Renee from Sparta, MI
- Parts Used:
- W10291024, WPW10259868, WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Range elements not working
Repair went really quick. The great thing about this was the GREAT service of PartSelect. I spoke with a representative who answered my question about one of the parts. I ordered all the parts and received them in a few days!!! My range looks brand new. I would recommend PartSelect to EVERYONE.
Was this instruction helpful to you?
Thank you for voting!