CDE850 Maytag Range - Instructions

I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.

Purchased 2 piece broiler pan from this site

I changed out the infinite switch without any problems. The indicator light was another problem. It wasn't the light that was bad, it was the indicator light lens that snaps into the panel. The light then attaches to the lense. The lense broke and the indicator light pulled away with the tension on the wires. Now I have to order replacement lens and will have a spare indicator light.

I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!

We made the mistake of taking the door apart before we received the replacement parts. After waiting several days, which was fine, the parts arrived. Then we had to figure out how it went back together. My wife and I did it and enjoyed working on it. However....after getting it partly reassembled, we (I) found four extra screws. We took it apart again and then put it back together. Turning the door over we found that the glass assembly had slipped. This meant that we had to take it apart again. This went on two more times LOL. Then the gasket gave us a couple of small fits as well. All in all it was a neat experience. I do suggest, unless you are experienced in appliance repair, to NOT disassemble the door until the parts arrive.

The comments from others on the website were a great help.

Thank you.

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

changed out switch

The contact spades were burned from 10+ years of use and the cook top module was worn. I disassembled the module, taped the top to protect the creamic cook top, sanded the metal and spray painted to restore the original white finish. On the bottom half I replaced one missing pop rivet and cleaned and spray painted the bottom to restore to the original black. When the contact spades arrived, I replaced the contact spades and reassembled the module. It now works and looks like it did when it was new.

I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

I enlarged the vent access hole from four (4) inches to five (5) inches to accomodate a larger pipe. I then purchased locally a 5" to 4" transition and installed it in the enlarged opening, and sealed the space with expanding foam for a bug-proof air-tight fit. On the inside of the house I attached a short length of 4" pipe to attach the dryer vent pipe. On the outside, in the place of the aluminum vent cap, I installed the 5" Jenn-Aire vent cover purchased from PartSelect.com. The new vent is large enough to completely cover the chiseled out masonry area, and the 5" outlet reduces air noise from the dryer, but best of all the new vent provides the high quality look I needed to match the brick of my new home.

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

Being a single Mom for almost 16 years I have learned to do everything. When the Jenn-Air oven baking element started on fire I freaked out. It turns out that PartSelect.com has the part as usual. I have ordered before for the same appliance and even though it is 15 years old you always have what I need. I removed the old one (two screws in back of oven), measured, logged on, ordered, and the next day installed the new baking element. Even I was able to do this and it fit and worked the first time!!!!

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.