CRE9700ACB Maytag Range - Instructions

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

I can't believe how easy this was to fix! I amazingly found the part on-line at PartSelect website. I love that you pick part by size, color, etc. I didn't have a part or model number, so this made it super easy! I ordered the part and got it in the mail within 2 days....YEAH! I got my screwdriver out and attached the peice, slid the drawer back in and shazam! it was fixed! Thank you PartSelect and kudos to the person that set up the way you order your parts......awesome! Thanks!

Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

The repair was easy as unplugging the range, unscrewing the bake element from the oven, pulling the wires out, unplugging the element and plugging the new element in. The oven works great after the repair! Too easy!! If I have to explain how I replaced the light bulb; you may not want to try it, you might hurt yourself.

Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove works great now.

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

I Unscrewed the attachment plates located at the back of the over. Pulled the element out so that I could "unhook" the prongs. Replaced the new element by clipping on the prong attachement (you will see where the electrical wires are). Screwed the plates back on and Vola! I'm baking again.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Rehooked up wires on new element, Slid the element in place. Replaced the two screws. Done, very easy.

My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.

First, I turned off the power to the stove at the circuit breaker.

Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.

I pulled out the heating element, disconnected the electrical leads, and installed the new one.

I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.

Hopefully, next time it won't be the day before Thanksgiving.

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.