MGR5870ADB Maytag Range - Instructions

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

replaced heat sensor

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Watch the video. Spot on instructions. Easy peasy.

oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.

We moved into a house with seemingly newer looking appliances. After the dishwasher broke and destroyed our floor, we found out that they were all twelve years old. Amazing the condition they were in after all that time.

The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed hot air to seep out.

So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.

The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.

We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.

Thanks!

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

The gas supply lines are included with the Assembly. The only tools needed to remove the old and install the new assembly were a phillips screwdriver and an small adjustable wrench. NOTE: The burners can be removed from the range top by carefully turning the burner to the right no need to lift the range top (I used a pipe wrench and very light pressure). $50 repair turned into $150 repair

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.