X3488VVDLT Maytag Range - Instructions

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.

Took the old levelling leg out and screw the new one in.

installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.

I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order

I killed power
Pulled the back panel
Pulled the door off
pulled light socket wires
reached in and bent in light socket tabs
knocked out light socket
slide in new socket
lifted top of stove (glass)
disconnected glass top wiring
pulled off glass top
pulled both side panels
removed both hinges,
installed new hinges
reinstalled side panels
reinstalled glass top,
reinstalled light socket wiring
installed back panel
installed door
restored power

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.

Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  tool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry

If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.

TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN

I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.

Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. So I just rested the new one on the old plate.

Pulled each wire slowly out and inserted it onto the new spark module.

Screwed in all the panels back and returned the stove to its proper place.

The range now works as well as the oven, but my broiler still does not light up.

Put a new one in.

Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.