CNP2010BXL Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from CINCINNATI, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from AURORA, MN
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No heat in oven
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from CLARKS SUMMIT, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Oven would not ignite
Very easy, video helped tremendously
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCES from AFFTON, MO
- Parts Used:
- W11400301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from ARLETA, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from LITTLE CANADA, MN
- Parts Used:
- W11400301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Simply remove and install new parts
Overall, it was painless and easy with zero problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from SAG HARBOR, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spotswood, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat up fully, smelled of gas.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from West Winfield, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nola from Enid, OK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove Would Not Light To Heat Up.
Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glynne from Dedham, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Oven was not working at all
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carmine from ABINGTON, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gas oven would not light
Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Sierra Madre, CA
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
oven took too long to light, then lit with a whump sound
I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Grafton, WI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
igniter glowed, but oven would not light or stay lit
The igniter was located in the bottom of the stove or broiler section. It was hard to get at, but with a little trial and error I figured out how to take the plate between the oven and broiler. Now the igniter was easily accessable. 2 screws on the igniter bracket, then simply unplug the electrical. The igniter supplied had the identical electrical plug (plug and play). The new igniter works like a charm-oven ignites in about 15 seconds. Piece of cake!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Replacement of igniter
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.
Was this instruction helpful to you?
Thank you for voting!