MER4600LS0 Maytag Range - Instructions

Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!

Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

turn the light on in the oven go to the breaker box and shut off power to the oven when light is out is good indicator remove two screws in back of oven that secure element to back then remove two screws on top inside the oven to almost finish removal. phillips head screwdriver and needle nose pliers and two small spring loaded clamps are all you will need to accomplish thismove the upper element side to side until the connectors are exposed in the back of the stove pull the two wires out about 4 inches should be enough place the spring loaded clamps on each wire so as to not allow them to slip back in the stove body. take the needle nose and while holding the clamp remove the connector from each wire once this is done place the new element in the stove and reconnect the clips on the end off the element move the wires and connectors back into the openings on the stove and replace the two screws replace the two upper screws check all screws for tightness go to the breaker box and turn on the power takes about thirty minutes

Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.

Replaced the burner switch.

Removed original broiler element, and found it was open. Replaced with new element.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Element burned out, ordered from Sears. Took over 2 weeks to get, originally sent wrong burner then shipped second one to wrong address. When I installed element I found that switch was also burned out . I ordered it from Parts Select & it was in the stove in 24 hours from the time I ordered it on line. Be assured I know where I will order my parts from now on

Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.

put it off a week before i worked on it but if you can replace a plug on a excord you can do this less than 5 mins

Removed the existing element and replaced it with the new one.

First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.