AER1360BGW Maytag Range - Instructions

I shut off the breaker in the fuse panel for the range ( recommended)
I had to unscrew the two mounting plates, unclipped two wire connectors.
Reconnected the two wire connectors ( pull off, push on)
Done
Flipped on breaker and was baking in less than 15 minutes.

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Removed burner and then burner pan.Then replaced pan and reinstalled burner.

Removed old element, pluged in new element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes

First I shut off the oven breaker, then I removed the racks and the oven door. I next removed the two retaining screws holding the element in place. I gently pulled the element forward to expose the blade connection. I disconnected the old element, attached the new element, slid it back into place and replaced the retaining screws. I remounted the door and turned the power back on. I did a test run on the oven. It worked perfectly.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.

Thank you

remove elements and replace bowles

Very easy, with only the removal of 2 screws.

Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes

repair was easy- turned off power at electrical box, emptied out the wire shelves in the oven. Unscrewed two fasteners holding element in place, pulled element out about 3 inches, unplugged electrical end connectors.
Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.

First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.

1) Unplugged the electrical cord and removed the oven door (only when easy); and, jockeyed the oven into better working area.
2) Removed about 9 screws holding rear sheetmetal backing plate to disconnect each of 2 electrical wires from the old element.
3) Removed 2 screws holding element to back of oven and 2 screws from small bracket supporting end of element to top of oven.
4) Replacement element was severely damaged. It was at the very bottom of a box 20 by 15 by 15.5 inches high with the large continuous bubble wrap stacked only on top. Each of the wire ends were sharply bent; one almost 180 deg. pointing in the opposite direction, and the other about 120 deg. The element itself was about 4-5 inches out of square. Using two large needlenose pliers I carefully bent each wire back to its proper place. Next I carefully exerted pressure on the element to gradually form it back to as near its correct shape as possible. (Only the inside of the shipping box showed the signs of possible damage.)
5) Installation- The element, from inside the oven, was placed back through the two holes in the rear of the oven and secured with 2 screws.
6) The bracket supporting the front of the element was slid onto the element and attached to the top of the oven.
7) Attached the 2 electrical oven wires to the 2 element wires, making sure there was good clearance to prevent any short circuit, plugged the oven cord in to 230volts, and checked it out with power to the broiler to give myself some confidence that the damaged wires would not quickly break. It seemed to work and I unplugged the oven.
8) Reinstalled the backing plate with the original screws, plugged oven back in, and moved the oven back to its place and replaced its door. It is working and my wife is cooking.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.