MER5752AAS Maytag Range - Instructions

Very easy to install with the advanced instructions you provided.

First, turn off the breaker to the range. Then just remove the 2 screws that hold the element at the back of the oven. Pull the wire connectors apart or push them off with a regular screwdriver. Instructions that I read said to make sure the wires don't fall back through the holes, but in our case the insulation held them in place. Reconnect the wire connectors to the new element and reattach with the screws. Easy!

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

My daughter repaired it without any problems.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Turned off the circuit breaker. Removed two screws - pulled the element out enough to get to clips connected to power. Removed old element - installed the new one. Replaced the screws, then turned the circuit breaker back on. Stove was repaired.

Went down stairs and turned the breaker for the oven off. Opened the oven door, took a phillips head wrench and took two screws out of the back of the oven that held the element in place. Slowly pulled the old element toward me. It seemed to catch on something in the back of the oven on the other side of the oven wall, so a jiggled the old element a little and it came out towards me with a mechanical connector and a wire attached at both ends of the element. I slipped the connctors off of the element and attached the connectors to the new element. Carefully slide the new element back through the holes and put the screws back in the small plates attached to the element. Went down stairs and turned the breaker back on. Turned oven on and it heated up even quicker than the old element.

First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

First I shut off the oven breaker, then I removed the racks and the oven door. I next removed the two retaining screws holding the element in place. I gently pulled the element forward to expose the blade connection. I disconnected the old element, attached the new element, slid it back into place and replaced the retaining screws. I remounted the door and turned the power back on. I did a test run on the oven. It worked perfectly.

I removed the two screws that held the element bracket in place. I then pulled the element out a few inches and disconnected the wires. I then reconnected the wires to the new baking element, pushed the wires back inside the oven and resecured the bracket. NOTE: turn off the power to the oven! I thought that since the oven was not on, I could safely perform this replacement...unfortunately I got zapped.

Easily removed the oven and had access to the rear in under a minute undid the 2 Phillips screws retaining the element and replaced with the new element I had ordered it was just so simple!

Thank you as you saved us calling out an expensive technician avoiding unreasonable time and costs expenditure

Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes

ordered new broiler pan

unscrewed element from oven, traded wire connections to new element, screwed new element in - saved myself a $75 service call