ACR4303MFW4 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cliffford from Rochester, MN
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner light was on all the time but burner was off.
Replaced the burner switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saranac Lake, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bowls had burnt on food
replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from GEORGETOWN, MA
- Parts Used:
- W10763667
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer Glide Snapped Off And Broke
Snapped in the new drawer glide. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
The Parts Came With No Instructions And We Couldn't Find Directions On Line.
We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Cameron, MO
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
could not control temp on burner
Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Levittown, NY
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
arcing within the cook top electric heat element and the receptacle.
Cut, splice and heat shrink.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce E from Oxford, MS
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the dial would not work unless the special screws, which are extra short, are utilized.
since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from Orange, TX
- Parts Used:
- 814399
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
intermittant power to "burner" eye
due to the cooktop age, part was not an exact duplicate. I had to drill new holes in the stainless steel for mounting and ground wire. I used a lot of kitchen matches to heat the shrink tubes over the twist connectors. I should have gotten a heat gun or torch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Elyria, OH
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original trim rusted
I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Louisville, KY
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element terminal connection loose caused overheating and carbon buildup.
Sanded element contact, replaced connector block. The easiest part of the task was ordering the part online. You made it unbelievably easy. I was amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Noah from Richardson, TX
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
corroded, rusted drip bowls
replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Grimsley, TN
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Bottom Door Trim Rusting
I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Seminole, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The large burner sometimes stayed on high too long, burning food
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Was this instruction helpful to you?
Thank you for voting!