Models > MGR6600FW1 > Instructions

MGR6600FW1 Maytag Range - Instructions

Jump to:

All Instructions for the MGR6600FW1
31 - 45 of 92
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Steven from SAN ANSELMO, CA
Parts Used:
WP9758079
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
replace bake ignitor ; flame spreader removal difficulty
As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WILLIAM from SAINT JOSEPH, MI
Parts Used:
WP9758079
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
WOULD NOT HOLD DESIRED BAKE TEMP
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glenn from ROANOKE, TX
Parts Used:
WP9758079
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Gas oven would shut off mid cook
Removed grills. Removed bottom plate.
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from EDEN PRAIRIE, MN
Parts Used:
WP9758079
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Igniter stopped sparking.
I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Isaac from MATTESON, IL
Parts Used:
WP9758079
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven would not completely heat up, only heating to about 150 degrees Temp.
contracted a repair service person
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from CEDAR SPRINGS, MI
Parts Used:
WPW10409945, WP8523175
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Front glass shattered, side trim broke and lower trim bent beyond repair
Followed the YouTube video and did it the correct way they showed. Note: side trim goes under the glass.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Killbuck, OH
Parts Used:
W10763667
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drawer guides missingJust
Just follow included instructions.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert Ruth from FERNDALE, WA
Parts Used:
WP3195097
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Corroded/greasy bottom oven tray
Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from SALEM, OR
Parts Used:
WPW10200660, WPW10031790
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replaced screw
By hand screwdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Victor from SAINT PETERS, MO
Parts Used:
WP9758079
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Stove would not light due to faulty electronic ignighter
Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Myron from Punta Gorda, FL
Parts Used:
WP8523175
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Paint peeling from strip
removed 3 screws holding the strip and replaced with new strip
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James E. from WAYNE, MI
Parts Used:
WP9758079
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Didn’t work
Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Teddy from PRAIRIEVILLE, LA
Parts Used:
WPW10184491
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Gas oven interment lighting. Pan was cracked and out of shape.
Loosen top two rear screws from the top pan. Remove top pan
Remove 2 front screws from bottom pan. Remove bottom pan. Reverse order.
Replace both pans.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Missouri Valley, IA
Parts Used:
WP3195097
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
last oven bottom was ruined by melted and burnt plastic
took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from ENID, OK
Parts Used:
W11594027
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MGR6600FW1
31 - 45 of 92