MER6600FZ2 Maytag Range - Instructions

After identifying the part and taking delivery of it, I opened the breaker for the unit and then removed the range top by taking out 2 Phillips screws and lifting the part away from the hinges in the back. The element was attached with only 2 spring loaded clips which I then removed, noting the numbered position of each. I then photographed the wiring (x4) from several angles and removed each of them. I attached the clips to the new element and reconnected the wiring to the main heating element and the sensor per the photographs. The element was then re-positioned into its mounting slots, the range cover was reattached with the screws and the unit tested once power was restored.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

I left the old broken hinge in place, & put the new hinge on the left side.

I took the door off the oven frame by releasing the hinge latches and lifting and pulling the door outward to remove it . Then I removed the glass outer cover by taking off the philips screws and then unscrewed the door hinges . I then reversed the order to replace it .

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall

Wrestled with it for ten minutes and then watched a youtube video on how to set the locks on the oven door hinges in order for the door to be installed. The video was instrumental

the door came apart fairly easy getting it all back together was another story lining up glass and panels that have already been heated was fun but its back together and working fine.... It should be noted that I have a warranty for the stove but the hoops I had to jump thru and the time it would take for the tech to come it was easier to do it myself!!

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.

The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.

Removed face plate (4 screws). Removed 2 screws holding manifold in place. Detached wires from the switch. No need to mark them - they don't have to go back on any particular terminal. Remove the switch from the manifold with an adjustable wrench. Replace with new switch (thread sealing compound on the new switch is sufficient - no need for teflon tape). Reattach wires and reassemble manifold and face plate. Easy fix!

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

First, view videos to know what is an active door range problem.
Second, when you know the problem, see videos on you tube and be sure you will replace the right part
Third, I go to Part Select, see reference video for your problem if you need and buy the part on line, good price, very quick delivery.