YMER6600FB2 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard Finneman from Muskegon, MI
- Parts Used:
- W11047722
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
None
Turned off power.Removed 2 screws, flipped top over, removed old element, replaced new element,turned over top,fasten down with 2 screws.Turned on power. Turned on burner,made coffee-took a brake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from POUND, WI
- Parts Used:
- WPW10434452
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch worked off and on but you could not set heat to a specified temperature.
Remove back panel 10 screws. Disconnect plug in fixture from switch. Front of range remove knob (it just pulls out) remove 2 screws, remove switch. To install reverse procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Farmington, NY
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad Element
Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Warren, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven light would not work--faulty socket
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from NICEVILLE, FL
- Parts Used:
- WPW10299226
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dual hinge replacement on oven door
My oven was assembled at the factory with half a hinge in left side ( no giant spring assembly) and in 15 months the right side hinge twisted and collapsed from bearing all the weight. First I thought I was only dealing with one bad hinge, and took the screws out of one side of door only and replaced hinge and was done in five minutes. Watched YouTube videos which were great and did the repair . Then I noticed the other hinge had no tension on it and did a complete disassembly of door and compared hinges and discovered the other shoddy assembly. I recommend you try to replace one hinge at a time. Take out screws on one side and finagle hinge into place. I did not do this and it took a long time. Rated repair difficulty due to several parts of oven door need to be aligned correctly to get the screws back in. Getting one side aligned caused the other side to become mis-aligned. Not rocket science but requires a lot of patience as you will redo it many times. I screwed the new hinges/steel channels they sit in into the inner door to help reduce the number of moving parts. Then aligned and secured door parts. I cut a 6” piece of straight wire from a coat hanger and stuck it through the screw holes to line them up. Worked very well, and after door was screwed together then I finally screwed the hinges to the outer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Fredericksburg, PA
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner control indicator light
Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WALDORF, MD
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wasn't preheating to temperature
Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from FRANKLIN, KY
- Parts Used:
- WP3149400
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element wasn't being controlled by the switch it would stay on high
Ordered a new switch and replaced the old one with it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Warren, CT
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Bad element replacement
Took off top and pulled out old element and plugged in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from STOW, OH
- Parts Used:
- W11047722
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burned out large range top element
After identifying the part and taking delivery of it, I opened the breaker for the unit and then removed the range top by taking out 2 Phillips screws and lifting the part away from the hinges in the back. The element was attached with only 2 spring loaded clips which I then removed, noting the numbered position of each. I then photographed the wiring (x4) from several angles and removed each of them. I attached the clips to the new element and reconnected the wiring to the main heating element and the sensor per the photographs. The element was then re-positioned into its mounting slots, the range cover was reattached with the screws and the unit tested once power was restored.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from KISSIMMEE, FL
- Parts Used:
- WPW10434452
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Bard burner switch
Removed rear panel disconnect power from wall removed old switch and replaced with new switch and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Reedsburg, WI
- Parts Used:
- W11047722
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner Element did not work
Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!
Was this instruction helpful to you?
Thank you for voting!