MGR4451BDW Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ben from Belen, NM
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shutting off, getting an F1 error on ECM
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Becky from Bussey, IA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat
Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SAN PEDRO, CA
- Parts Used:
- WP3412D021-09
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Electrode broken on end and would not ignite the burner
It was a very easy repair. I just connected the two wires to the bottom of the electrode and set the burner on stove top and turned it to the right to lock in place. Turned burner knob on and burner worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mz from COLUMBIA, ME
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FLORISSANT, MO
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broiler wouldn't turn on(ignite)
Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from REDFIELD, SD
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
j just look at it and figure how itcomes apart and reverse when installation complete easy
took out burner and remove ignite r and reinstall a new one simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Forked River, NJ
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Smell of gas and would not always light or took forever to preheat
Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Woverine Lake, MI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven wouldn't heat
I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Goshen, IN
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The main gas valve to the oven would not stay on.
Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gloucester, MA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Broiler would not ignite
I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Bethpage, NY
- Parts Used:
- WP74009014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Front glass broke
Unscrewed bottom piece; put on tape and new glass; re-installed bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mokena, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old igniter wouldn't get hot enough to allow gas flow
Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from JOHNSBURG, IL
- Parts Used:
- WP74011675
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle broke off.
Took the door off the hinges and placed it on the floor. Removed the trim from the oven door. Removed bracket holding broken oven handle on. Using the same bracket, replace the oven handle. Replaced the trim and put oven door back on hinges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from new york, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The igniter was just glowing and it didn't open the gas valve
I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.
Was this instruction helpful to you?
Thank you for voting!