11EA-1KW Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- scott from newtown, CT
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't get hot
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Otto from Bridgeport, CT
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor lights but gas does not come on
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luz M. from North Providence, RI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven didn't get hot
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- graham from littleton, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven ignighter would glow, but oven would not work
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from SALEM, OR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not heat. Broiler was fine, just no oven.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from breaux bridge, LA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light
open oven door remove bottom tray pull off two screws unplug wire remove old part install new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Girdwood, AK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Mayville, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ignitor would heat enough to open gas vavle to lite oven
unplugged the oven, unplugged the ignitor and removed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Dearborn, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat to temp and could smell gas.
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neville from Lithonia, GA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would not Light
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Canton, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles H. from Mosinee, WI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The oven igniter would glow but oven would not lite.
I unpluged the electrical cord first. Then pulled the stove away from wall. Next removed oven racks, the bottom of the oven. Then removed the deflector plate over the burner. The next step I removed the broil pan. Now the oven area is empty. Nice and easy to remove the igniter with nut driver. Two screws and wire nut that are behind the stove wall. Now I just reversed the procedure. Very easy. The only thing I'm not sure where the insulation block go's. The wires go through back oven wall hole. There was no insulation there before? So I put a small piece just behind the igniter over the wire. Will this catch fire I don't know? If someone knows let me know. Other than that it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thakur from South Richmond Hill, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Oven wouldn't heat
I removed the two screws that hold the element. This took most of the time because one of the screw broke. Then I unplug the power,took the igniter out and disconnect the wire and reverse the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from EAST MORICHES, AL
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
the oven would not ignite
I unpluged the oven, removed the oven door by slideing it off the hinges, removed the racks, took the bottom pan out exposing the igniter,while attempting to remove the 2 screws holding the igniter to the bracket, I discovered that they where stripped so I had to use vise grips to remove them. I went to the hardware store bought replacements and installed the igniter. I then removed the protective cover over the wires, stripped them put on the wire nuts provided with the kit put the protective shield back pluged the unit in turned it on, checked it, then put it back together. The stripped screws were the only difficult part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Chokoloskee, FL
- Parts Used:
- 12400034
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the knob broke off
installed new control unit had to use the old dial so it would match . Toughest part is the cleaning! needed it.
Was this instruction helpful to you?
Thank you for voting!