35BN-8 (1X) Maytag Range - Instructions

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

Remove old drip bowl from the range and put a new one back.

New receptacle element. I am a girl and I did it.!!!!