CDE8300ACB Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Control switch would not operate
Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Albany, GA
- Parts Used:
- WPY702338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn door seal on oven
takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from GARIBALDI, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one was plugged
Pulled out old one and slipped in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from East Greenwich, RI
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced the current warn-out grease filter
removed the old by pulling it out of track and replaced it with the new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from North Reading, MA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
front burner stayed on high
We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lorton, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
RF burner would not heat
1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentine from Bow, NH
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Hubert, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new grease filter
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)
:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Lafayette, LA
- Parts Used:
- 74011338, WP7518P054-60, 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn out / burned grill and components
very easy - not really a "repair" more of a face lift, although the grill was unusable.
Parts were perfect - Used it the same night.
Parts were perfect - Used it the same night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Anna Maria, FL
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new grease filter
Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Berlin, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter Worn Out
Remove cover and install
Was this instruction helpful to you?
Thank you for voting!