MER5751BAW Maytag Range - Instructions

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Was very difficult because door handle broke off on Holloween 2020. I looked into model number and ordered part same day. Money was taken out of my account almost immediately. Email said it would be sent out within 7-10 days. A while month went by. I emailed them twice asking about my order. They never got back to me.

So after 2 months, I posted a review on Facebook of my experience with this company. Within an hour of my review going up on Facebook, they contacted me and I gave them my order info. It was sent out the next day.

So the only reason they took care of it is because of the bad public review on Facebook that I posted.

They did refund me the shipping cost. But I will never use this company again. This never should have gotten as far as it did. The only reason they talked to me after they took my money is because of the bad public review.

I followed peoples instructions here, and it was not very difficult.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Removed old hinges, fabricated new mounting plates from 16ga steel plate. . . Cut new hinges to fit in available space. . . Drilled and tapped new mounting holes and adjustment tracks. . . Shortened existing springs to fit new configuration. Installed new hinges.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

Removed the oven door an removed some screws. After that it was pretty much self explanatory from there. Real simple project !

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Turned off breaker, moved unit and unplugged the unit. Safety first! Removed the oven door, removed two Phillips screws, pulled out the heating element, removed two clips.

Installed new element in reverse order. Put back the door. Plugged in unit, moved back into place and turned on breaker. Tested the oven, and it worked great. Maybe 20 mins total, very easy and saved at least 200 bucks vs calling a repair guy.

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Pulled the drawer and removed the oven door by pulling it upward. Then removed the two hex head screws which loosened the old hinge and pulled it down out of the side of the oven box. Replaced the new hinge in the position of the old one and installed the two hex head screws. I replaced the oven door and that was when I realized the part was wrong. The parts description in the view on the website was one number off and I replaced the broken hinge and ordered from another site the right number. That hinge works.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.