PER3525ACW Maytag Range - Instructions

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Just took the old one out and put the new one in. Very easy!

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

Very easy to install with the advanced instructions you provided.

My daughter repaired it without any problems.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

easily pulled old seal out and push new seal in place simple and quick.

Very easy, with only the removal of 2 screws.

First I shut off the oven breaker, then I removed the racks and the oven door. I next removed the two retaining screws holding the element in place. I gently pulled the element forward to expose the blade connection. I disconnected the old element, attached the new element, slid it back into place and replaced the retaining screws. I remounted the door and turned the power back on. I did a test run on the oven. It worked perfectly.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes

repair was easy- turned off power at electrical box, emptied out the wire shelves in the oven. Unscrewed two fasteners holding element in place, pulled element out about 3 inches, unplugged electrical end connectors.
Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.