U34GN-4TKXW Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from MOUNT HEALTHY, OH
- Parts Used:
- 12001655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had an F2 message go off then F3 when I tried to turn the stove on
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Grand Ledge, MI
- Parts Used:
- 1430283
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusty drip trays
finally after years of searching for trays of this size with no luck in local stores, I was able to find and purchase 2 sets, one set for my daughter, which we were able to put in place to clean up our stoves and make them more appealing . Thank-you for your prompt service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billye from San Antonio, TX
- Parts Used:
- 1430283
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Range burner drip pans were rusted and old
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the future for needed parts.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the future for needed parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OSCAR from BRISTOL, CT
- Parts Used:
- 7711P172-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace clock-adjust knob
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clymer, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not turn on
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Westcliffe, CO
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven did not heat up in bake mode.
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from haskell, NJ
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F 3 signal on display pad every time oven warmed up
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from West Winfield, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glynne from Dedham, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Oven was not working at all
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from SAG HARBOR, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- june from wills point, TX
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Belen, NM
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shutting off, getting an F1 error on ECM
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELMER from BONNEY LAKE, WA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from DAYTON, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas would come on, would not ignite. Oven not heating.
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from CINCINNATI, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this instruction helpful to you?
Thank you for voting!