CPL1100BDW16 Magic Chef Range - Instructions

First I removed the old burner head by twisting it counter clockwise by using wide channel lock pliers. When It completely came off, the burner head had deteriorated so much that it almost came apart. When I took off the 2 wires from the burner head it also easily came apart. The burner-head was in really bad condition. I cleaned the whole area and connected the 2 wires to the new burner head and hand tightened in a clokwise direcrtion. It took 20 minutes to install.

Removed the top burner and the door on oven. Took out the bottom plate and the shield on top of the pilot light.

It was pretty much a plug it in job

I first switched the old burner to a new position and different ignitor wiring. The problem persisted in both places, so I bought a new burner assembly and now the burner lights immediately. Very happy and a very simple replacement.

I was looking at replacing the stove and saw the $1200.00 price tag! So I found this web site and paid $100.00 to fix my old one. It was very simple. I twisted off the old burners by sliding off the two connecting wires. Cleaned the area around the seating area of the burners. Hooked the wires on the new burners and twisted them back in place! Tested them to insure that was the problem and was done! Thank you for saving me $1100.00!!! Next I am getting grates so the whole stove will look band new!

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Turn off power then turn to take old burner out ,
disconect 2 wire , .
Connect electric wire with new burner press in then turn and clock . Turn power on then start stove
and check .

snaped them into oven cavity attached temp bulb job complete

put it on, perfect

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Shut off the gas before you do anything! Remove the top front face cover by removing the four screws. Remove the three gas lines that go into the oven valve. remove the screws that hold down the manifold bar. Slide bar to the front and free from the burners and main valve. Remove the small bolt on the underside of the manifold that holds in the oven valve to the manifold. Remove old thermostat bulb from it's bracket inside the oven and pull through to the top of oven. Then remove the old valve. Remove rubber seals and transfer them to the new valve if you don't have new ones. Replace the new valve. Insert thermostat bulb on the end of the wire into the hole and down into the oven. Mount thermostat bulb into bracket. Then just reinstall in the same order that you took it apart. Then run the oven and check the new thermostat out to make sure it is working properly.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

I ordered the two replacement burners. When they arrived I equipped myself with WD-40 spray, rubber mallet and a rubber gripper I used to use to open canning jars. Sprayed the WD-40 around the burner base and let it sit for 20 minutes. Made a mental note of the location of the sparker of the burner, to remember to put the new one in the same way. Gathered my courage and gently wacked the burner with the mallet all around it. Then grabbed the burner with the gripper and gave it a firm ¼ circle twist counter clockwise. It came apart with no problem. Disconnected the two electric wires by slipping them off their sockets. Removed all the loose rust and cleaned around the burner. Reconnected the wires with the new replacement burner and dropped it in its place. Wiggled it a little until it fit back into its original location and twisted it ¼ circle clockwise. Done, just saved myself the price of a new stove! Note: There is no need to shut off the main gas valve.