68-4567-40 Magic Chef Range - Instructions

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

removed drawer from track replaced supports on track and one on the drawer.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Screwed in light bulb and glass protector

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well