DF251300 Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from rochester, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Long delay before ignition slow preheat
Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble
Did not have gas smell, but ignition took 6 minutes
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble
Did not have gas smell, but ignition took 6 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from gore springs, MS
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
stove would not preheat above 175
My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENE from ELKHORN, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven Would Not Light
Changed the igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fort Dodge, IA
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not ignite
Removed bottom tray in oven, used nut driver to remove igniter, pulled oven out from wall and unplugged cord, did steps in reverse and repair was done. Very good tip on what was wrong with oven and how to diagnose the problem. I will defintly use your tips and purchase parts from you in the future if the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from Prescott, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would take up to 30 min to ignite once turned on
Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Lake View Terrace, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
gas oven igniter would glow, but oven did not turn on
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Oxford, PA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat. Electronic ignitor (heating element) was not heating/not getting to temperature to open the automatic gas valve.
Make sure the knobs are all in the off position before starting the work. You may feel more comfortable shutting the gas valve off behind the stove or in the basement first, just make sure you fire the burner and let the gas that is left in the line burn off.
Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.
Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from warrensburgh, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven didnt lite
removed 2 screws on element then unpluged it then replaced it with new one easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from patchogue, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven bake would not come on
First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Wheaton, IL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner would not lite. There was an intermittent spark from that burner.
Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Glendale, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven stop working
I opend the bottom cover, which had for screws then , opened 2 screws that atached the igniter to the main gas pipe and pulled the whole wiring out and disconected the wiring , ordered the igniter two days later, I put the whole thing together in less than 5 minutes . put back the cover. and I tried it , everything was cool , accutaly hot and working .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn Truax from Key West, FL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
All the burner caps had badly rusted; tip-off was the smell of gas.
Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from North Ridgeville, OH
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not get hot would never turn on or turn on and never restart
Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great
Was this instruction helpful to you?
Thank you for voting!