3882XRA Magic Chef Range - Instructions

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes properly, the heat stays in the oven!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. Once off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS

I removed screws that hold cover and put cover aside. I removed the buttons and removed glass cover. I pulled panel out far enough t get tswitch wires and installed switch. Be very careful not to let wires touch metal.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

First-my daughter needed her pizza and I didn't want to even think about the cost of a new range. So she did some research online about replacement parts. Lo an behold, Partselect.com was our answer.

We received the part in a few days and replaced it with just unscrewing a few screws.. AFTER we unplugged the range. We also used a tool that I would describe as a nail remover/lifter to get the end off of the wire connection. Needless to say, we were rookies and had no experience with this type of repair and were so proud that we were able to spend less than $30.00 to fix our oven.
Thanks to Partselect.com for making it easy to do this repair on our own.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

no tools needed

First I shut off the power at the circuit breaker.Then I removed the racks to make room to work.I then removed the 2 screws holding the element in place and pulled both sides out approx.3 inches.After carefully disconnecting the wires,I put the new element in to place and repeated the steps backwards.