61S04PAW Magic Chef Range - Instructions

My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.

Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.

Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.

The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the utility drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".

The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping the new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

Took the old levelling leg out and screw the new one in.

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.