61S14WAA Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gino from ARLETA, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from LITTLE CANADA, MN
- Parts Used:
- W11400301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Simply remove and install new parts
Overall, it was painless and easy with zero problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from ALBANY, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Santa Maria, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gas burner on stove top not lighting ,other 3 work fine.
Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCES from AFFTON, MO
- Parts Used:
- W11400301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HILLSBOROUGH, NJ
- Parts Used:
- 7733P099-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old Valve Knob Broke at Base
Simply pull off the old knob from the stem, then push the new knob onto the stem. NOTE: This part works for the POWER BURNERS on the Maytag MGR4450ADH - the stems and knobs of the regular burners are different.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Long Grove, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
smell gas on oven start up
took oven tray out and loosened igniter and replace same works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALAN from LUCK, WI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter Would Glow But Stove Wouldn't Light
I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the part and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lino Lakes, MN
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom oven burner wouldn't light.
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Newton, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven ignitor would glow but took 30 - 40 mins to heat
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Allison Park, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Oven wouldn't heat. Igniter was broken.
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Somonauk, IL
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove top burners ignition were not working
1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.
Was this instruction helpful to you?
Thank you for voting!