CGL1100ADQ Magic Chef Range - Instructions

I lifted up the bottom insert of the inside of my oven and then followed the instructions on this site. Originally I purchased the wrong igniter, so I would encourage you to look at yours and make sure you are buying the right part. I am a complete novice. Even with my purchase debacle, my oven was back up and running within 5 days (total cost was $60). Do this even if you are scared of a screwdriver. Just remember to turn off the gas first. Make sure you've turned off the gas by trying to light a burner (if your burners are otherwise working correctly). If it doesn't light, the gas is off and there is nothing to be afraid of. The igniter is far enough away from the gas pipe that I wasn't afraid of breaking it and once I saw how the oven was put together, I wasn't afraid of working on it. And, if you need to return anything, the return policy is awesome.

unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.

I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!

Got the part, changed it, works great. That's all

used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.

I replaced the igniter.

easy

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

I opened the door partway to remove the door. Then I removed the bottom heat shield plate by pulling it towards me and lifting it up. I removed the two screws holding on the igniter, then with the the disconnect removed the old ignitor. I plugged in the new ignitor, replaced the screws, replaced the heat shield, replaced the oven door, and was done in ten minutes.