6895VRA Magic Chef Range - Instructions

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed 4 screws holding top cover in place.
Took out knobs.
Removed side slides holding panel glass in place
Unplugged Touch panel from ECU
Pulled off old touch panel.
Used WD-40 to remove old adhesive from panel glass
Had to enlarge timer knob hole on new touch panel to fit old knob
Installed new touch panel and plugged back in
Cleaned old greasy areas that were not touched in years (anal retentive action)
Re assembled everything else

6 days and no F1 error or beeping

Very fast shipping from PartSelect.com

Thank You

Turn off power ,pull off clock and timer buttom ,lift the light cover , remove a screw on each side of the light, ,than with the stuby screwdriver remove one screw on each side at bottom of front glass, front glass should come loose. peel off the control plate .it is just stuck on the glass front. you will then see where the wire plug go's , unplug the old discard the entire front panel you just peeled of ,,feed new panel wire through the hole and replug it . it only go's one way,peal and stick the control panel., put glass front back ,replace the screws,

Slide smooth stove top back. then removed 2 screws on top and 2 on bottom of clock and control mechanism. disconnected the touch pad and peeled it of f front of stove. Cleaning the adhesive from under the touch pad took the longest. I did that with rubbing alcohol. I then peeled the backing off the new pad and put it in place. Reconnected the clock and control mechanism and replaced the screws. No more alarms.
When I had called Whirlpool (the now makers of Magic Chef). They told me I would have to have a technician diagnosis the problem and if what I thought was wrong, the part was no longer available. The technician had told me if they could get the part it would cost $289-$389 to replace. Thanks to Partselect and everyone here it cost me $100 and I had the part the next morning.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.

Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.

Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).

Pry out the old electronic control panel.
Lift the range top and disconnect wires to keep it aside for easy working.
Disconnect the wire clips for the old panel and remove.
Connect the new panel aligning the clips.
Stick the new panel on the front which has an adhesive backing.
Reconnect the range top wires and put back in place.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wire and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.