B35HA-92X-ON Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara a from Huntington, NY
- Parts Used:
- WP660532
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Emmett, KS
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner no longer worked.
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bellefonte, PA
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not work
slide stove out unplugged it took six screws out put new one in transfered wires pluged back in and it works thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula Collins from Needham, MA
- Parts Used:
- WP3191454
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old coil broke.
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Shirley, IN
- Parts Used:
- WP3191454
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken terminal
Simply removed the old heating element and plug the new element terminals into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from South Bend, WA
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
A switch on a front burner went out
I first removed the back panel that covers the switches from back of stove; then I removed the wires and put them on the same numbered wires on the new switch; put the new switch in place with the wires connected to it; installed the 2 front screws and put the back cover on again & it took about 10 min and saved about $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from San Antonio, TX
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Burner wouldn't heat (wiring failure)
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolland from New Port Richey, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Broiler element split after oven self-cleaning
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard C from San Jose, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Frayed and exposed receptical wires in cartridge
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Reston, VA
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replaced Broiler Element
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Elba, AL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burnt out
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alex from huntington, NY
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace element
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Thornton, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out, broke circle, heat only half
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this instruction helpful to you?
Thank you for voting!