3527WUV Magic Chef Range - Instructions

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.

removed drawer from track replaced supports on track and one on the drawer.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Pretty simple, except the element melted very close to one end, so the screw holding the element to the rear of the stove was partly melted also. Had to drill it out & used a nut & bolt to secure the new element.
Apart from that, it was a breeze. As others have done, I re-tightened the lugs that the element plugged into.
Suggest a "test heating" before using stove: mine had a strong odor on first use, fine afterwards

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I should have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.

Super simple. My husband ordered the part. It arrived in 3 days. The old element plugs right into cables on both sides of the back of the oven and are secured to the rear wall with screws. I unscrewed the plates, detached the wires on each side and slid the new ones in place. It was that easy and took me about 10 minutes.

. First I removed the two screws that hold the ace. I thenelement in place. I then pulled the element out about inches and disconnected the two wires...)

I unplugged the oven, sat the flash light in the oven and removed the two screws that hold the element in place. I pulled the element out and diconnected the two metal wire clasps from the element. Connected the new element, made sure the clasps were secured. Slid the wires back in and replaced the screws. Tested the oven, it heats up to correct temperature. I am a women and it was real easy thanks to the other repair stories I read.

I shut the breaker off at the main power box.
In the oven, I loosened two screws to remove the old element (parts now, after the burn-out). I pulled the old element out of the back wall of the oven to expose the wire connections. I detached the simple sliding wire connectors. Done with removal. I waited for the new element to arrive (one week). Installed easily. Turned on the breaker and baked a few potatoes. Very simple.

unscrew 2 screws, pull 2 connectors off, put in new part in reverse order - easy fix.

unscrewed the element and pulled it out, then put the new element in.

Removed back of stove (6 screws), puled clips loose. Two screws inside oven, pulled out old element. slid new one in, replaced screws, slid on clips replaced back panel. Don't forget to unplug the stove frist.