3468XVW-X Magic Chef Range - Instructions

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

I took the broiler pan out of the shipping container and put it in the oven.

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.

Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.