38FY-2CX-MO Magic Chef Range - Instructions

replaced drip pans with correct type

remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.

very easy

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

Before I give procedure steps, please note the following observations that I had.
a)If AC power is plugged in and an electrical terminal touches the frame, the resulting arc may require that you reset the GFCI or the circuit breaker.
b)The clock failed to run until it was properly mounted (including the back cover in place).
c)Movement of wires can cause them to work loose at EITHER end of the wire.
d)Attempting to operate the clock, Start and Stop knobs may extremely difficult or otherwise ineffective unless it is properly mounted. Fully depressing these knobs / shafts is difficult.

The numbered steps below are how I would do it correctly based on what i learned.
1)I unplugged gas range power cord.
2)Re-positioned range to access the back without damaging the flexible gas supply line.
3)Removed the rear cover (#2 Philips) behind the timer.
4)Verified no voltages present
5)Judged that the front cover glass needed removal - removed timer knobs and front glass cover
6)Removed existing clock timer by using a WIDE flat blade screwdriver to depress the rear of each clip and pushing the time our the front. Old part has damaged gears and one axle end out of position.
7)Fed old timer back through the opening to the rear to assist with transfer of wires.
8)With the assistance of a helper, transferred the wires one at a time from the old to the new timer.
9)Fed new timer back through the opening to the front; aligned and snapped into place.
10)Replaced front glass and knobs.
11)Plugged in AC cord (first did inspection for snug connections and potential shorts).
12)Tested buzzer feature of the timer. Unexpected that the buzzer was intermittent.
13)Unplugged power cord. Found & tightened loose connection - not at timer but other end of one of the timer wires at the chassis connection strip.
14)Reinstalled the metal back cover & plugged in the AC cord.
15)Set the timer start and stop times to one hour before present time. (Knobs need to be depressed.)
16)Set clock to present time by depressing the knob IN and rotating it clockwise to the correct time. As clock is manually advanced to the timer start and stop times, verified that each knob popped out. The hand on the clock for the timer moves also, but when you release the knob pressure, the knob pops out and then you set the timer past the buzzing to zero.
18)I put the oven through a self-cleaning cycle. This uses the new timer; starts when the START button pups out and stops when the STOP button pops out. Of course there are other controls you need to manipulate for the self-cleaning cycle i.e. CLEAN settings and the door lock.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

After I removed the piece of metal separating the two wires, I inserted the unit with no problem.

I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Simply removed the old heating element and plug the new element terminals into socket.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

just plugged it in!

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.