3488VVV Magic Chef Range - Instructions

Unscrew the burners an install new ones! Anyone could do this.

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

I took the broiler pan out of the shipping container and put it in the oven.

I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.

Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!

I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.

I followed peoples instructions here, and it was not very difficult.

I followed the video and it was incredibly easy. I shut the breaker off (we live in an apartment, and pulling the plug on the stove wasn't possible). I lifter out the old burner (the gasket underneath was corroded, and I just threw it out, as the newer burners are self-sealing); removed both the igniter wire and the ground wire (I needed a pliers to tug the igniter wire off); attached the new burner; replaced the burner; turned on the power; and voila!

USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.

Very easy, video helped tremendously