31311WAA Magic Chef Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!

Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.

Replaced the oven ignitor. Toughest part was removing old screws.

After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!

During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!

I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the electrical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

I attempted to use the knob: it didn't fit. However, I located original paperwork with the model number on it and then I came back to partselect.

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!