31203SAW Magic Chef Range - Instructions

The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

The installation was very easy.

The knob fit right into place and that was it.

No screws or tools were necessary.

There was a "D Shaped" slot in the back of the knob that slid right into the metal piece attached to the stove.

The delivery was very quick and the ordering process was very easy.

Replaced with a new one.

I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. After removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.

Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...

Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3

slide latches in rear of floor panel forward and remove.

The burner was leaking a rust colored dirt and shooting flames all over the place. The top came off and I needed channel-locks to get the bottom half out. The wires were hard to get off and I broke one connector off so I soldered the wire on to the new part which fit the stove top perfectly. It still took less than a half hour to replace. Without problems it should take about 5 minutes.

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS