35JA-26X-ON Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Yelena from San Francisco, CA
- Parts Used:
- W10823704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The front left side burner was broken.
We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Nesconset, NY
- Parts Used:
- W10823707
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Original burner stopped heating up
Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Hot Springs Village, AR
- Parts Used:
- W10823704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
surface burner failure
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Schertz, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Nashville, TN
- Parts Used:
- W10823704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Lower left Surface Element burnt
1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.
Was this instruction helpful to you?
Thank you for voting!