38FB-42TXW Magic Chef Range - Instructions

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

ordered new broiler pan

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

Pulled out the old burners and put in the new ones.

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com

Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Remove two screws back panel and remove sensor two screws inside top oven.

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.